Lights

Can You Cut LED Strip Lights?

Can You Cut LED Strip Lights?

Whether you’re hoping to enlighten your kitchen pantries or backdrop illumination your TV, with LED strip lights, there’s an answer for everything. Inclined toward their flexibility, LED strips to comprise a progression of LED producers introduced onto a thin, adaptable circuit board. There’s only one reason to worry. Most LED strips come as lengthy reels somewhere in the range of 3ft and 16ft long. Will they keep on working on the off chance that they are managed down? Now the question arises can you cut led light strips? So the answer will be yes Indeed, LED strip lights will continue working after they’ve been cut the same length as you cut along the assigned lines. Driven strips are composed of a few individual circuits, so each cut line separates the finish of one circuit and the beginning of another one. Cutting somewhere else on the LED strip will cause that circuit, and possibly the entire strip, to stop working.

Sliced To Custom Lengths:

With regards to LED strip lights, there is no ‘one size fits all.’ But whether you want lights that are adaptable or unbending, monochromatic or RGB, waterproof or non-waterproof, most LED strips will share one thing: for all intents and purposes, they can be sliced to custom lengths. At customary spans all the way through, each LED strip will be straight or speckled with dark lines. Circuits are completely shut at these places, so these are the most secure spots to cut your LEDs without bringing on any harm. These cutting lines will be different on each LED strip. When in doubt of a rule, they’re normally every 3 LEDs. Thus, for instance, on the off chance that there are 30 LEDs for each meter, the cutting lines will ordinarily be every 10 cm. On each side of the dark cutting line, there ought to be a copper-binding structure.

How To Cut Led Light Safely?

Customizing the length of the LED light strips is relatively easy. Here is my step-by-step guide.

  1. Start by testing the lights to make sure they work. It may seem obvious, but in most cases, cutting or soldering the lights will void the warranty, so it’s best to double-check.
  2. Next, you will need to determine how long your LED strip should be. To do this, you need to measure where you want the lights to go. Be as specific as possible with this. You will then choose the cut line on your LED strip closest to this measurement length.
  3.     Cut accurately along the cutting line with a sharp knife or scissors. Take your time and remember that LED strips are designed to be cut so that you won’t be afraid. You will also need to decide how to connect the strip to the power supply. Most coils come with a plug pre-installed, but cutting the LED strip removes this, so you’ll need to install a new one.

Reconnecting Led light:

Get your measurements 

Decide if you need a straight connector or a 90-degree angled connector.

Use standard craft scissors to cut along the predetermined cutting line of the copper section. This section of copper is on your light strip, spaced every few inches. Each section of the light strip should have the same number of copper sections. This is necessary for the connector pins to function.

Prepare your gapless plastic connection or jumper and remove any sticky backing to allow for a clean finish.

Gently push each section of the light strip.

Use the small clamps on the connector to snap the string lights into Make sure both sides of the light strip are facing the correct direction. The polarity must be correct for the voltage to flow.

Connect the string lights and check the lights on both sides of the 

If you do not have a light on the new section of the light strip, check the polarity.

Read More Related Blogs

Led Lights That Are Not Recommended For Cutting:

There are several types of thin tape that are not recommended for cutting. The first is a strip of light controlled by a separate IC chip. These black chips are placed every few diodes along the light strip. And hence the name, they only control a few diodes one at a time. This allows each part of the light strip to display a different color. And if you make cuts, you run the risk of damaging the whole piece or the roll.

Small Scissor Mark:

If you have your own light strip, take a look at the copper section. You can cut them along the markings if they are marked with a small “scissor” symbol. If you don’t see the scissor symbol along the copper marker, you likely can’t cut your LED light strip. Also, look for large black individual IC chips about the size of an eraser head. This type of light band cannot be cut.

So it’s no big surprise that they’re quickly turning into the most well-known type of LED lighting. That’s it! Driven strip lights can be tweaked to meet the needs of their customers, regardless of how large or small.

 

Leave a Reply

Your email address will not be published.